Artec BCU Test on Active And Passive Stratocaster Pickguard

Artec BCU On Board Active controllable parametric EQ

Artec BCUThe Artec BCU is an active parametric EQ coupled with a booster. BCU stands for Band Control Unit. It’s a small and cheap active circuit that you can install easily on any electric guitar or bass, owning an active or passive electronic wiring. It changes the natural sound of your pickups and expands the possibility from the tone of single coils to a fat and powerful tone of humbucker pickups.

In the video included in this article, I am testing the Artec BCU on two different pickguards installed on two separate Stratocaster.

I performed the first test on an active pickguard featuring two single coils and one humbucker from EMG. I installed it on my LabStrat before installing it on a custom Strat.

The Humbucker is an EMG 81 and I have no info concerning the two single coils. I have had them since 1988. They were installed on a custom Godin, and I didn’t like them much. I uninstalled them over 20 years ago, and they have been sleeping in a drawer since. The 81 was given to me by a friend and I never used it either.

>>>Multi effects for guitar<<<

Finally, I like them pretty much; they sound cool at a Strat. There’s a difference of volume between the coils and the humbucker. I’m going to work on that when the pickguard is going to be installed on the right guitar. As of now, the humbucker is much louder. It also has to do with pickup height, but as you can see in the video, the pickguard is not even properly installed.

Back to the Artec BCU

The Artec BCU features are quite simple. To activate the circuit, you have to pull the potentiometer. I find this strange. I would have preferred to pull it to shut it off. I think it’s more natural, most of the push-pull pots are wired the other way around. This is not something crucial, and you can get used to it fast.

The knob set on 0, delivers a fat boost on your pickup that sounds like a humbucker. If you drive a single coil with it, you’ll get a driven humbucker sound. If you use it on a humbucker pickup, it will push your pup even more, but the difference in sound is going to be less important.

The knob set on 5, gives a more neutral boost. It shifts the high-midrange slightly and cuts some of the low-midrange. Use the potentiometer to fine-tune frequencies.

The knob set on 10, produces a leads bright tone. The low and high frequency are boosted while the midranges are cut in a sort of ‘V’ shaped EQ. It makes your humbuckers sound like a single coil and the single coil even brighter.

>>>Demon TS808 Tube Screamer<<<

Artec BCU
Artec BCU Push-Pull version

I covered every setting multiple time in the video using all combination of pickups on both pickguards. One trick I like on single coil is to use a crunch or distorted sound and to set the Artec BCU to 10. It renders an almost clean sound. Then, rolling the potentiometer toward zero restores the lead sound up to extreme rock distortion when your reach zero. It’s extremely useful. You can set your sound once and for all and balance it manually using just one tone pot. Brilliant.

On humbucker it’s different. The zero setting gives a huge distortion sound. It makes your pickup even fatter. If you roll it up to ten, the V shape EQ softens the lead sound. It can be useful when going from rhythm to solo mode.

I found the Artec BCU more efficient on single coils than humbuckers and on passive pickups than active pickups.

Nevertheless, I like it a lot on the active pick scratch I’m working on right now. I’m going to install it on the second guitar I’m using in this video. Not that I don’t like the result of the Artec BCU on passive pickups. It concerns the overall wiring and the difference with other guitars that I have. It will be more diverse with active electronics. I already have a passive SSH strat.

>>>Electric Guitar<<<

Watch the comparison test video

>>>Hervé Senni YouTube Channel<<<

Installing the Artec BCU

It is very easy. The only problem is the battery location. On all my strats featuring active circuits, I routed a battery slot and used a battery case to be able to change them quickly. You can also locate it inside the guitar knowing that an Artec BCU can run more than 4000 hours in continuous use. Just do not forget to unplug the guitar. Otherwise, you’ll empty the battery fast.

AS far as installation goes. You need to replace the mono output jack with a stereo one. Solder the heat and ground as usual. The third leg on the output jack is intended for the battery ground wire. It turns it off when a jack is not inserted. It explains why you have to unplug your guitar when you are not playing, even during breaks at a gig.

>>>Guitar Pedals<<<

installing Artec BCUThe Artec BCU needs four wires to solder

  1. In: Solder the wire from the master volume pot’s output.
  2. Out: Solder a wire to the heat of the output jack, replacing the former one.
  3. Ground: Solder a wire to the back of the master volume pot with all the other grounds.
  4. B+: Solder the + red wire from the battery.

That’s all there is to it. You are ready to rock.

Be cautious that this thing delivers lots of output. Take care of your ears and work on your settings. Your guitar ring is on vitamins with that thing.

Please do not hesitate to give your two cents or ask anything you might want to be clarified. Use the form below and I’ll do my best to answer you.

>>>Herve Senni Streaming Sites Catalog<<<

signature


Distribute your music using Distrokid

Use my VIP Link and get 7%

>>> Distrokid<<<

Twitter
Visit Us
Follow Me
YOUTUBE
YOUTUBE
INSTAGRAM
SOCIALICON
Author Profile

I am Hervé Senni, a pro musician and performer, Composer and arranger for quite some time. My main musical instrument is the electric guitar. I am also a bass player, mandolin, Ukulele player. I also invented string instruments.

Over the years, repairing and improving electric guitars that did not have to be upgraded converted me into a self-taught luthier.

Read More

This post is also available in: French

6 Comments

Enjoy this blog? Please spread the word :)

  • Twitter
    Visit Us
    Follow Me
  • YOUTUBE
    YOUTUBE
  • INSTAGRAM
  • SOCIALICON
Twitter
Visit Us
Follow Me
YOUTUBE
YOUTUBE
INSTAGRAM
SOCIALICON